Computerized tire recycling EPT/tyre shredEPTEPT
The initial phase in tire recycling procession
Weighty responsibility physique
Hooks and cross pulling die created of forty five# metal, tempered and quenched
Outfitted with protection frame keeping away from the risks during operating
Two collection: Hydraulic one and mechanic a single
Straightforward to work and modify spare elements (hooks and cross pulling die)
Reducing tires into parts prior to shredding
Small tire pieces are easier to process in shredder
Knives made of YG-twenty metal, EPT utilizing time
1 clamping cylinEPTand a single reducing cylinder
Outfitted with a roller platform to approach large tires
The higher-potential shredEPTwas EPTly deveXiHu (West Lake) Dis.Hu (West Lake) Dis.ed for direct size reduction of tires into cleanly minimize tire chips, measurement 50×50 mm. Slicing shafts for the production of bigger tire chips are offered high torque at reduced speed cut even the strongest tires into pieces.
All building attributes are made for constant procedure in orEPTto attain optimum throughput costs at least expensive fees.
Very exact tolerances between the chopping knives produce cleanly cut tire chips at minimal power use.
The reducing knives manufactured of higher quality alloy steel can be re-sharpened and reused which will increase the provider daily life and lowers the operating expenses.
The full cutting chamber is lined with hard dress in plates.
Huge doors enable for straightforward entry into the cutting chamber.
The shear amongst the two rollers will make tire chips into powders as effectively loosen rubbers, steels and textiles
Roller physique created of forged steel
Area of roller created of alloy metal, welded when worn out
One flat floor roller and one teethed roller, high throughput of powders
Bottom created of solid iron
Crisis cease when overload
Length in between the two rollers can be modified.
Hard gear EPT
Outfitted with screening EPT, magnetic separator and fiber separator, ninety nine% purified rubbers will be received.
Finals: 8-thirty mesh
Closing Solution(5-one hundred twenty mesh tyre powder), As photograph:
The identical time, Tyre powEPTis widely use in a lot of sector. It can make rubber tile, reclaimed rubber, automobile portion Ect others.
2-Reclaimed rubber Producing Line From Tyre Powder:
one. Dynamic desulfurization tank (1 sets
Dynamic desulfurization tank
two. Open up miXiHu (West Lake) Dis.ng mill (you need 2-3 sets)
1. Diameter of roller: 450mm
2. Operating length of roller: 1200mm
three. Pace of entrance roller: 24.26m/min
four. Friction ration of two rollers: 1: one.27
5. Max gap: 15mm
6. Capacity: twenty five-50kgs
seven. Wieght: 2000kgs
eight. Motor EPT: 55KW
9. Dimension: 6150*2280*2000mm
3. Rubber refiner( 1 sets)
one. Entrance rolle diameter: 480mm (drum )
2. Rear roller diameter: 612mm (drum)
three. Operating size of roller: 800 mm
4. Entrance roller linear velocity: 22.97m/min
5. Speed ratio of 2 rollers(entrance/rear): 1: one.82
6. MAX Hole: 15mm
7. Motor EPT: 55KW
eight. Dimension: 4700*2100*1480mm
Final EPT(RECLAIMED EPT):
|EPT tire pre-processing , you will get lt 50*50MM rubber crumb|
|one||One hook debeader||LS-1200||1||eleven KW|
|two||EPT tyre cutter||WTC-one hundred twenty||1||5.five KW|
|three/four||EPT tyre shredder( with EPT tyre conveyor)||ZPS900||1||sixty one.5 KW|
|Rubber powder processing: you will get 3-eight MM rubber powder,at the very same time, different the fiber and metal wire|
|five||Tyre crusher||XK560||1||75 KW|
|6||Huge conveyor gear||BCL-eight||two||two KW|
|7||Small conveyor gear||BCL-three||one||1.one KW|
|eight||Huge Magnet separator||BMS22||1||two.2 KW|
|nine||Tiny Magnet separator||SMS-1||1||1.one KW|
|ten||Huge Shaking monitor||BSS-eight||one||7.five KW|
|eleven||Little Shaking display screen||SSS-three||1||three KW|
|twelve||Fiber separator||FS110||one||eleven KW|
|thirteen||Good grinder||XMF420||one||32.four kw|
|14||Circle shaking monitor||DIA600||one||2.2 kw|